Washing machine size guide and space check

Compare a washing machine and its stated clearances with your measured space. Your measurements stay in your browser.

Your measured space

Measurement unit

Changing units converts the measurements.

The closed machine

Required clearances

Use the maker’s value. Enter 0 explicitly.

Use the maker’s value. Enter 0 explicitly.

Use the maker’s value. Enter 0 explicitly.

Use the maker’s value. Enter 0 explicitly.

Door or lid space

Opening check

Space comparison

Meets entered sizes

Meets entered sizes. Smallest margin: 30 mm spare.

Remaining space

Smallest margin

30 mm spare

Available space compared with entered requirements
DimensionAvailableRequiredMargin
Width650 mm620 mm30 mm spare
Height900 mm870 mm30 mm spare
Depth700 mm650 mm50 mm spare

Door and lid opening space is excluded.

Entered sizes only, with results in millimetres. This is not installation approval.

Measure the machine and installation space

A washing machine size guide compares the machine’s outside measurements and required clearances with the space available. Use the exact model’s installation drawing.

Measure the narrowest usable width and the height above the finished floor. For depth, measure from the rear wall to the nearest obstruction in front.

Machine measurements must include the closed door, controls and other protrusions in the maker’s overall dimensions. Allow for the installed foot height.

Fisher & Paykel’s installation drawings separate product dimensions from minimum cavity dimensions and show open-lid height. Hoses also affect the installation depth.

Enter the specified left, right and top gaps. The rear allowance must cover both the stated rear gap and any extra depth the installation drawing requires. Use the larger allowance. Leave a clearance blank until you have its specification. Enter 0 only where the maker permits it.

For a front door, enter the extra forward reach beyond the closed machine. For a top lid, enter the extra height above the machine’s highest closed point. Subtract closed overall height from the required open height if the manual supplies both.

The opening check compares that outer reach with your measured space. It cannot trace a door’s full swing around neighbouring fittings.

Understand kilograms and external dimensions

A washing machine’s kilogram capacity describes a dry laundry load. It does not state the machine’s width or the space it needs.

Fisher & Paykel’s washer guide defines rated capacity by maximum dry weight. Fabric care and the chosen programme also affect how you load the machine. Use the programme instructions for the laundry you actually wash.

These two manufacturer examples have the same stated capacity and different outside dimensions.

ModelDry capacityHeightWidthDepth
WH8560E1 front loader8.5 kg850 mm595 mm566 mm
WA8560E1 top loader8.5 kg1,045 to 1,075 mm600 mm600 mm

The WH8560E1 specification supplies the front-loader dimensions. The WA8560E1 specification supplies the top-loader dimensions. These are product measurements, before installation clearances and opening space.

Compare your usual dry load, bulky items and programme limits separately from physical space. Household headcount alone does not determine the right capacity.

Read the space comparison

The result meets your entered sizes only when every required dimension is no larger than the measured space. A shortfall in one dimension is enough to fail this comparison.

The fictional example opens with a 650 mm wide, 900 mm high and 700 mm deep space. Its machine measures 600 mm wide, 850 mm high and 600 mm deep.

The example assumes 10 mm at each side, 20 mm above and 50 mm behind. Those figures illustrate the arithmetic. They are not recommended clearances for a real machine.

DimensionRequired spaceSpace left
Width600 + 10 + 10 = 620 mm30 mm
Height850 + 20 = 870 mm30 mm
Depth600 + 50 = 650 mm50 mm

The smallest remaining margin is 30 mm. Reducing available width to 610 mm gives a 10 mm width shortfall, even though height and depth still meet the entries.

Selecting Top lid with 500 mm extra reach raises required height to 1,350 mm and leaves a 450 mm shortfall. The tool uses the greater of top clearance and lid reach. It does not add them together.

Selecting Front door with 400 mm extra reach raises required depth to 1,050 mm. The example then has a 350 mm depth shortfall.

Installation also depends on the delivery route and turning space, floor support, levelling, accessible connections and the model’s installation instructions. Check doorways and stairs separately. A rectangular space comparison cannot certify these conditions.