Button battery size guide by code and dimensions

Look up five maker references by battery code or measured dimensions.

Compare a cell

Look up by

Across the cell’s widest circular face.

The cell’s total thickness, from face to face.

Display units

Five maker references. Measured entries use millimetres.

Dimension matches

1 listed match

1 listed match.

Matching references

Matching maker references, physical size and electrical details
ReferenceDiameter × heightChemistry / voltage
Panasonic CR203220 × 3.2 mmLithium manganese dioxide · 3 V

A size match does not establish electrical suitability. Use the device’s specified replacement.

Read the cell code and device specification

A button battery size guide compares the cell’s code and physical dimensions. The device’s instructions determine the replacement’s electrical requirements.

Read the full code on the cell and the device’s battery specification. Diameter measures across the circular face. Height is the cell’s total thickness.

Chemistry describes the cell’s materials, while nominal voltage describes its stated electrical voltage. Equal dimensions alone cannot confirm either requirement.

This reference contains Panasonic CR2016, CR2025 and CR2032 cells, plus Energizer A76 and 357/303. The Energizer datasheets identify A76 as IEC-LR44 and 357/303 as IEC-SR44.

Codes outside those records receive no inferred equivalence. Rechargeable cells are outside this reference. A similar numeric suffix does not establish a substitute.

Compare the physical size

The code lookup shows the selected maker’s dimensions. Measurement lookup returns every listed cell whose dimensions or drawing ranges contain both entries.

For example, selecting Panasonic CR2032 returns 20 mm diameter and 3.2 mm height, with a nominal voltage of 3 V. Panasonic lists CR2025 at the same diameter but 2.5 mm high. CR2016 is 1.6 mm high.

Maker referenceListed codesDiameterHeightChemistry / voltage
Panasonic CR2016CR201620 mm1.6 mmLithium manganese dioxide, 3 V
Panasonic CR2025CR202520 mm2.5 mmLithium manganese dioxide, 3 V
Panasonic CR2032CR203220 mm3.2 mmLithium manganese dioxide, 3 V
Energizer A76A76 / LR4411.25 to 11.6 mm4.9 to 5.4 mmAlkaline manganese dioxide, 1.5 V
Energizer 357/303357/303 / 357 / 303 / SR4411.25 to 11.6 mm5 to 5.4 mmSilver oxide, 1.55 V

Panasonic publishes single dimensions for these CR cells. Energizer publishes the drawing ranges shown here. The lookup adds no measurement tolerance to either source.

For a fictional measurement-only example, enter 11.5 mm diameter and 5.2 mm height. Both Energizer records match their drawing ranges.

A76 is alkaline at 1.5 V. The 357/303 is silver oxide at 1.55 V. That shared physical match cannot choose the electrically suitable replacement.

A 20 mm diameter with a 2.4 mm height gives No listed match. This means the reference contains no match for both entries. It does not identify the cell.

Display units change the result’s units while measured entries stay in millimetres. Inch values are rounded for reading. Use the source millimetres when comparing small differences.

Source dimensions come from Panasonic’s CR2016 specification, CR2025 specification and CR2032 specification. Energizer’s A76 datasheet and 357/303 datasheet supply the drawing ranges and electrical details.

Use the specified replacement

Use the replacement specified by the device manufacturer, including the complete code and required chemistry. Follow its polarity and battery-compartment instructions.

Keep new and used button batteries out of children’s reach. Change cells on a flat surface away from children and secure the compartment afterwards.

The ACCC’s button battery safety guidance says to tape both sides of used cells. Keep them in a child-resistant container out of reach until taking them to a battery recycling drop-off point.

If you suspect a child has swallowed or inserted a button battery, call the Poisons Information Centre immediately on 13 11 26. Call 000 if the child is bleeding or has difficulty breathing.