Dishwasher size guide by opening and product dimensions
Compare your opening with a dishwasher’s documented dimensions and clearances.
Dimension comparison
Within entered space
Within entered space. Width 2 mm spare, height 10 mm spare, depth 20 mm spare.
Opening and required space
| Dimension | Opening | Required | Margin |
|---|---|---|---|
| Width | 620 mm | 618 mm | 2 mm spare |
| Height | 865 mm | 855 mm | 10 mm spare |
| Depth | 650 mm | 630 mm | 20 mm spare |
Product: 598 mm wide, 845 mm high, 600 mm deep. Allowances: left 10 mm, right 10 mm, top 10 mm, rear 30 mm.
Closed rectangular envelope only. Results use millimetres. Door access and installation suitability need separate checks.
Measure the opening and product
A dishwasher size guide compares the opening with the exact model’s dimensions and stated installation allowances. A nominal 60 cm label cannot establish the full space required.
Measure width at the narrowest point between the cabinets. Measure height from the finished floor to the lowest underside of the benchtop. Check both at the front and rear.
Measure depth from the rear obstruction to the intended closed front position shown in the installation drawing. Record protruding fronts separately when the drawing allows them.
Use the product width, installed height and depth for that same reference. Include feet, worktop or furniture panel only as the model’s drawing specifies.
| Type and model | Declared product size | Separate installation detail |
|---|---|---|
| Freestanding SMS6HCI01A | 845 mm high, 600 mm wide, 600 mm deep | The specification lists a 30 mm removable worktop. |
| Built-under SMU6HCS01A | 815 to 875 mm high, 598 mm wide, 573 mm deep | Its stated niche depth is 550 mm. The front reference differs. |
| Fully integrated SMV6HCX01A | 815 to 875 mm high, 598 mm wide, 550 mm deep | Its stated niche is 600 mm wide. Check furniture-panel details in its installation drawing. |
Bosch’s freestanding specification, built-under drawing and specification and fully integrated drawing and specification show these model-specific figures. They are not universal dimensions or clearance rules.
For a built-under product, do not compare the full front-to-back product depth directly with a niche depth that excludes its projecting front. Match the drawing’s measurement points first.
Enter each required allowance from the exact model’s instructions. The rear allowance must include any extra depth required for connections behind the product. Avoid counting the same space twice.
If a requirement is missing, leave that field blank. The comparison stops until you supply it. Enter 0 only where the manufacturer’s guidance supports zero additional allowance.
Compare the installation envelope
The required width is product width plus the left and right allowances. Required height adds the top allowance. Required depth adds the rear allowance.
The fictional example has a 620 mm wide, 865 mm high and 650 mm deep opening. Its product is 598 mm wide, 845 mm high and 600 mm deep.
It assumes 10 mm at each side, 10 mm above and 30 mm behind. These fictional allowances demonstrate arithmetic and are not installation advice for a real dishwasher.
| Dimension | Required space | Remaining space |
|---|---|---|
| Width | 598 + 10 + 10 = 618 mm | 2 mm |
| Height | 845 + 10 = 855 mm | 10 mm |
| Depth | 600 + 30 = 630 mm | 20 mm |
Changing opening width to 618 mm gives an exact boundary with 0 mm remaining. Reducing it to 617 mm gives a 1 mm shortfall. Height and depth still meet the entries.
Clearing the rear allowance leaves a missing requirement. The tool stops the comparison instead of assuming zero. Every entered product dimension and allowance remains visible beside its unit.
A positive margin is spare space beyond the entered requirement. An exact boundary leaves no spare margin for measurement error or an uneven opening.
Check the installation requirements
Dimensional fit does not establish that a dishwasher installation is suitable. The closed envelope leaves door movement and service requirements outside this calculation.
Check the open door against adjacent cabinetry, handles and the space you need to load the baskets. An integrated furniture panel also needs its specified fixing and plinth geometry.
The built-under and fully integrated Bosch examples list 1,150 mm depth with the door open at 90 degrees. That measurement covers a different state from closed product depth.
Follow the exact model’s ventilation and moisture-protection requirements. Check water supply, drainage routing and electrical requirements separately, including access to their connections.
Confirm the delivery path, floor support, levelling and fixing requirements with the installation instructions before arranging installation. Supply the model number and measurements when an installer checks the site.