Microwave size guide by cavity and installation space

Compare your dish and available space with listed microwave dimensions and ventilation clearances.

Your dish

Measurement unit

The chosen unit applies to every entry.

Dish shape

Include handles and any lid overhang.

Measure the complete dish with its lid.

Available space

Open countertop space only.

Microwave reference

Dimension comparison

Dish exceeds limits

Dish and interior

Dish against listed limits
DimensionDishListed limitComparison
Cavity width28 cm30.6 cmWithin limit
Cavity depth28 cm30.7 cmWithin limit
Cavity height8 cm20.8 cmWithin limit
Turntable support28 cm25.5 cmOver by 2.5 cm

Cabinet and ventilation

Space including listed clearances
AxisRequiredAvailableComparison
Width54 cm60 cm6 cm spare
Depth37.5 cm50 cm12.5 cm spare
Height35.9 cm45 cm9.1 cm spare

Sharp R-211D: 20 L. Cabinet 44 cm × 32.5 cm × 25.9 cm (width × depth × height). Clearances: left 5 cm, right 5 cm, rear 5 cm, top 10 cm. Countertop or open shelf. No cupboard, cabinet or built-in installation.

Dimension screen only. Check door access, usable tray height and free rotation with the actual dish.

Dish exceeds limits.

Separate cavity and external dimensions

A microwave size guide needs two comparisons: whether your dish fits the interior and whether the appliance has enough space for its ventilation requirements.

Measure a round dish across its widest point, including handles. For a rectangular dish, use the full width and depth. Include the lid in its height.

The cavity’s rectangular dimensions describe its inside envelope. Advertised litres describe volume, so two 20 L microwaves can have different heights or outside dimensions.

The turntable is a separate measurement. This tool uses a conservative full-support rule: a round dish’s diameter or a rectangular dish’s diagonal must fit within the glass tray’s diameter.

A rectangle’s diagonal is the square root of its width squared plus its depth squared. That diagonal describes the circle swept by its corners during rotation.

A dish outside the full-support limit needs an actual model-specific assessment. It can be smaller than the cavity and still extend beyond the tray.

The cavity height also needs a physical check above the fitted tray. Door openings, rounded walls and internal fittings can reduce usable room.

Work a dish-and-space example

The example compares a fictional 28 cm round dish, 8 cm high, with Sharp’s R-211D reference. The available open space is 60 cm wide, 50 cm deep and 45 cm high.

The cabinet measures 44 × 32.5 × 25.9 cm in width, depth and height. Adding the listed ventilation spaces gives a requirement of 54 × 37.5 × 35.9 cm.

The outside comparison passes, with 6 cm spare across the width. The 28 cm dish exceeds the 25.5 cm turntable support limit by 2.5 cm, so the headline reads Dish exceeds limits.

Change the dish diameter to 25 cm. The headline becomes Within listed limits. At 25.5 cm the support comparison is exactly at its boundary, with no extra allowance.

For a rectangular example, choose Rectangle and enter 20 cm width with 15 cm depth. Its 25 cm diagonal fits the 25.5 cm full-support limit.

Each axis must pass independently. Extra width cannot offset a depth shortage. The result keeps every failed dimension visible beside its shortfall.

Choose millimetres, centimetres or inches for your entries. Changing the unit reinterprets the numbers already entered, so convert them into the chosen unit before comparing.

Follow the installation instructions

Sharp’s R-211D operation manual supplies the cavity, cabinet and tray figures. Its installation section requires at least 10 cm above and 5 cm on each side and behind.

Sharp permits countertop or shelf placement and rules out cupboard, cabinet and built-in installation. A rectangle large enough for the numerical clearances does not change those restrictions.

The Panasonic NN-ST25JW instructions use 15 cm above, 10 cm behind and 5 cm on both sides for the countertop arrangement shown. Selecting it changes the outside requirement.

The tool retains both side clearances. It does not apply an alternative flush-wall arrangement or approve an enclosure.

For a built-in microwave, use the exact model’s approved trim kit and installation drawing. A trim kit changes the ventilation path and opening requirements.

Keep vents clear and leave room to open the door and remove a hot dish. Check the supporting surface and the actual model’s electrical supply requirements.

Sharp’s instructions require an earthed supply and an accessible outlet. Have a qualified electrician resolve an unsuitable connection before installation.