Nose ring size guide by gauge and diameter

Convert nose-ring gauge and compare hoop openings using a named jewellery chart.

Read the jewellery

Reference chart
Thickness entry

Enter a whole gauge number. Unlisted gauges keep the opening comparison.

Plain circular hoops. Results compare jewellery dimensions only.

Compare openings

Entry units

Across the inside, excluding the wire.

The other hoop’s stated inner diameter.

Opening difference

1.5 mm smaller

Jewellery dimensions

Wire thickness

0.8 mm

Nominal gauge

20g

Model outside

8.1 mm

Reference opening

8 mm

Maria Tash FAQ: 20g is nominally 0.8 mm thick.

Your hoop opening is 1.5 mm smaller than the comparison opening.

Relative hoop drawing

Inner opening6.5 mmReference opening8 mm

Ideal round wire, closed circle and no decoration. Screen size is relative. Results use millimetres.

Separate thickness and hoop diameter

A nose ring’s gauge describes the wire thickness. Its inner diameter measures the open space inside the hoop. Compare both dimensions when reading two product listings.

This guide uses the selected maker’s nominal jewellery chart. In the Maria Tash gauge reference, 20g is 0.8 mm and 18g is 1 mm. A lower gauge number means thicker wire.

The FreshTrends measuring guide and gauge chart lists 20g as 0.81 mm. The tool preserves that difference between the charts instead of applying one formula to every maker.

Choose Measurement when a product states an exact thickness. A measurement gets a gauge label only when it matches a supported chart row. The tool never rounds to the nearest gauge.

Both references support 20g, 18g, 16g and 14g here. Maria Tash also lists 19g, while the FreshTrends selection includes 22g. An unlisted gauge keeps the opening comparison and shows an unsupported-row notice.

These references do not convert sheet-metal or knitting-needle gauges. A jewellery gauge number alone also leaves the hoop diameter unspecified.

Compare a jewellery-size example

The fictional example uses a 20g hoop with a 6.5 mm inner opening and compares it with an 8 mm opening. Under the Maria Tash FAQ chart, its wire is nominally 0.8 mm thick.

The first opening is 1.5 mm smaller. For an ideal closed circle made from uniform round wire, outside diameter equals inner diameter plus twice the wire thickness.

That gives 6.5 + 2 × 0.8 = 8.1 mm across the outside. The solid ring in the drawing uses those dimensions. The dashed circle shows only the comparison opening.

Correct comparison: match a listed 8 mm inner diameter to another inner diameter. Incorrect comparison: treat the example’s 8.1 mm outside diameter as its inner clearance.

The drawing is a dimensional model of a plain hoop. It excludes hinges, open gaps and settings. Screen zoom changes its physical size, so use the labelled measurements instead of measuring the display.

Inch entries convert using exactly 25.4 mm per inch. A 0.25 inch opening becomes 6.35 mm. Results stay in millimetres to keep small jewellery dimensions readable.

Check the actual product and piercing

A product’s stated dimensions take precedence over a general gauge chart. For example, the Maria Tash plain hoop listing labels its 18 gauge option as 1.02 mm. Its FAQ rounds that reference to 1 mm.

Use the product’s stated 1.02 mm in Measurement mode when comparing that item. An exact gauge match can then be absent even though the listing names a gauge.

A decorative top’s width measures the decoration. It does not establish wire thickness or hoop clearance. For a nose stud, use the maker’s wearable-length drawing because a post length is different from a hoop opening.

This tool compares dimensions and does not select a size for a piercing. Healing stage, piercing angle and individual anatomy remain outside its result. Material suitability also needs a separate assessment.

Keep the maker’s complete drawing and stated tolerances with your comparison. Before changing jewellery or a piercing size, have a qualified piercer assess the actual item and piercing.