PC case size guide by component and case dimensions

Check card length, air cooler height and motherboard support against two Fractal case references.

Case and components

End to end, including the shroud. Above zero, up to 2,000 millimetres.

Full installed air cooler height. Above zero, up to 1,000 millimetres.

Installed configuration

Combined fan depth at the card’s height. Above zero, up to 100 millimetres.

Radiator depth in front of the card. Above zero, up to 200 millimetres.

Result unit

Dimensional check

Limits met

3 of 3 checked limits met.

Limits met. Both entered dimensions have 11 mm spare.

Component comparison

Entered components against the selected case limits
ComponentYour entryCase limitComparison
MotherboardATXATX / Micro ATX / Mini ITXSupported
Graphics card length300 mm311 mm11 mm spare
Air cooler height158 mm169 mm11 mm spare

Dimensions enter in millimetres. This checks only the listed limits.

List the component dimensions

This PC case size guide compares graphics card length, air cooler height and motherboard format with two Fractal Design case references. Each comparison uses the selected case’s declared limit.

Choose Meshify 2 Compact or Meshify 2 Compact RGB. Their graphics card limits differ, even though both belong to the same case family.

Motherboard format describes the mounting layout. Both references list ATX, Micro ATX and Mini ITX. An E-ATX selection returns “Not listed” because these references do not declare that format.

Measure the graphics card from end to end, including its cooler shroud. Card height reaches towards the side panel, while slot thickness occupies space beneath the card. These are separate dimensions.

The tool compares card length only. Check card height, occupied slots and the power plug’s required space against the component drawings before choosing an enclosure.

For an air cooler, enter its complete installed height. A liquid cooler needs a supported radiator position and space for its fans. The air cooler entry remains a separate dimension check.

Compare the installed configuration

A front radiator reduces the space available for a graphics card. In the standard Meshify 2 Compact, Fractal lists 341 mm with its front fan and 360 mm without it.

For a front radiator and fans, Fractal’s configuration instructions subtract their combined thickness from 366 mm. The tool also caps the result at the declared 360 mm empty-mount limit.

The default example uses a 25 mm fan and a 30 mm radiator. Its card limit is 366 - 25 - 30 = 311 mm. A hypothetical 300 mm card leaves 11 mm.

The hypothetical 158 mm air cooler is 11 mm below the 169 mm limit. With an ATX motherboard, all three checked limits are met.

The RGB reference uses its own 345 mm factory-fan limit. It hides the standard model’s front options because that radiator formula does not establish the RGB model’s clearance.

Fractal’s case manual shows the card and cooler limits in its configuration diagrams. It also shows radiator mount options. The front mount accepts radiators up to 360 mm. The manual limits the width of 140 mm and 280 mm front radiators to 145 mm.

A top radiator can be up to 240 mm, with motherboard components no higher than 40 mm beneath it. Check memory and motherboard heatsinks against that restriction.

“Limits met” means the entered values meet these listed checks. At an exact limit, the table says “At limit”. No extra assembly allowance is added.

Comparisons use the entered measurements before display rounding. Changing the result unit leaves the entries in millimetres and shows the table in inches. One inch equals 25.4 mm.

Verify connectors and assembly

A dimensional result cannot establish full PC compatibility. Check the exact component models and their installation drawings before ordering.

Match the motherboard’s mounting holes to the case standoffs. Confirm its processor socket and memory support separately from its case format.

Check power supply capacity, connector types and cable reach. Leave the connector maker’s required cable-bend space beside the graphics card’s power socket.

Radiator length labels describe a mount class. Compare the complete radiator body, end tanks and tube exits with the case drawing. Account for drive cages or brackets that share the space.

Plan how each component enters the case and how you will reach its screws. A part can meet a length limit while its insertion path or connectors still obstruct assembly.

Cooling performance depends on the complete build and airflow arrangement. The card-length and cooler-height comparisons do not predict temperatures or choose fan settings.

Before buying, compare the exact case variant’s manual with your parts list. Resolve an exceeded dimension by changing the component or the supported case configuration.