Plant pot size guide by internal dimensions

Compare a container with pot interiors and your chosen clearance. Your measurements stay in your browser.

Your current container

Measurement unit
Container shape

Widest outside span, including the rim and feet.

Widest outside span, including the rim and feet.

From the supporting base to the highest rim.

Pot interiors

Your pot’s clear opening, inside the lip.

Your pot’s narrowest clear span, including ribs.

From the actual support surface to the inside rim.

Clearance allowances

Applied around the container. Enter 0 explicitly.

Total extra height for lifting and headroom.

Dimensional matches

2 matches

Compare both references

Conservative pot interior comparison
ReferenceListed sizesDiameter marginHeight margin
TOYOGO GP3504Meets listed sizes15 mm spare90 mm spare
Your measured potMeets listed sizesExact allowance10 mm spare

Your measured pot

The reference rectangle shows only the limiting diameter and usable height. It does not trace the pot wall or ribs. The hatched area is the entered allowance, with the total vertical allowance shown above the container. Rim 220 mm Limiting span 190 mm Height 200 mm Container envelopeRequired envelope Each side 5 mm Vertical allowance 10 mm
Selected reference and required envelope
MeasurementSize
Inside rim220 mm
Limiting inside span190 mm
Usable inside height200 mm
Required diameter190 mm
Required height190 mm
Gap on each side5 mm
Vertical allowance10 mm

Conservative dimensions only. The full outside envelope must clear the narrowest listed span.

2 matches. Required diameter 190 mm and height 190 mm.

Measure the actual container

This plant pot size guide compares a container’s outside envelope with the inside of a round replacement or cover pot. The result includes your entered allowances.

Measure width and depth across the widest parts of the nursery container, including its rim. Measure height from its supporting base to its highest rim.

For a round container, measure across it in two directions. The tool uses the larger span. A rectangular container uses its corner-to-corner diagonal to clear a round interior.

Measure the cover pot inside its lip, then find its narrowest clear diameter lower down. Include any ribs, ledges or inward curves.

A tapered base can be much narrower than the opening. Measure usable height above the surface that supports the nursery pot. An insert or reservoir can raise that surface.

The comparison uses the narrowest span for the container’s entire height. A tapered nursery pot can nest where this conservative check reports no match. Trial fitting resolves that case.

Product specifications explain which measurements describe a product. An outside diameter or litre label alone does not state usable clearance.

Compare a cover-pot example

The hypothetical example has a round nursery container measuring 180 mm across both directions and 180 mm high. It allows 5 mm around each side.

The required diameter is 180 + 5 + 5 = 190 mm. A 10 mm vertical allowance brings the required height to 190 mm.

The entered cover pot has a 220 mm opening, a 190 mm minimum inside diameter and 200 mm usable height. It meets both entered requirements.

The diameter margin is exactly zero after the allowance. The height margin is 10 mm. These are remaining margins after your allowances, not the total physical gaps.

MeasurementRequiredPot interiorResult
Diameter with side gaps190 mm190 mm minimumExact allowance
Height with a taller container210 mm200 mm usable10 mm short

Change the container height to 200 mm to reproduce that failure. The 220 mm rim still admits the 190 mm diameter requirement. Usable depth fails.

The built-in TOYOGO GP3504 specification lists a 385 mm external rim, a 315 mm internal opening and a 205 mm internal base.

It gives 280 mm internal height and an internal drainage reservoir. The tool uses 205 mm as its limiting listed diameter.

For the default container, that leaves 15 mm diameter margin and 90 mm height margin. The listed dimensions do not map every rib or the reservoir’s supporting level.

Use your actual interior measurements for the second reference. The diagram labels the dimensions used in the calculation. Its dashed box shows the required envelope, without reproducing the pot’s wall shape.

The example’s allowances illustrate arithmetic. Choose the clearance needed for your container and any lifting arrangement. A listed-size match still needs a physical trial fit.

Check drainage and plant needs

A dimensional match describes container space. It does not decide when to repot, how much root space a plant needs or whether its growing conditions suit it.

Keep the nursery pot’s drainage route clear. After watering, let the plant drain and empty collected water from the outer container.

The Royal Horticultural Society’s houseplant guide explains why drainage and emptying water-filled saucers protect the root zone.

For a direct replacement planting pot, assess root space and the plant’s needs separately. This comparison does not calculate a recommended planting volume.

The monstera pot size guide covers the separate plant-specific sizing question.