Pool table size guide by playing area and room
Compare a pool table’s playing area, cabinet and cue clearance with your room.
Rectangular clearance
Clearance fits
Centred table, entered cue and movement allowance.
Clearance fits. Required room: 538 cm by 426 cm.
Room requirement
Length needed
538 cm
Width needed
426 cm
Length shortfall
0 cm
Width shortfall
0 cm
Clearance at each side
| Side | Cushion to wall | Spare after cue + movement |
|---|---|---|
| Head end | 163 cm | 5.92 cm |
| Foot end | 163 cm | 5.92 cm |
| Left side | 164 cm | 6.8 cm |
| Right side | 164 cm | 6.8 cm |
Declared table
- Reference
- Centennial 8 ft
- Playing length × width
- 223.52 × 111.76 cm
- Cabinet length × width
- 256.54 × 144.78 cm
Identify playing area and cabinet size
This pool table size guide compares your room with the table’s playing area and outside cabinet. Cue clearance starts at the cushion edge.
A nominal 8 ft label identifies a table size. The cushion-to-cushion playing length and the outside cabinet length are separate measurements.
Brunswick’s Centennial 8 ft has an 88 × 44 inch playing area inside a 101 × 57 inch cabinet. Its 9 ft version plays 100 × 50 inches inside 113 × 63 inches.
The references come from Brunswick’s Centennial dimension sheet. The calculator converts its inch measurements directly because the sheet’s metric column is rounded.
For another model, choose Your table drawing and enter the maker’s playing and cabinet dimensions in centimetres. Include the widest fixed projections in the cabinet measurements.
Calculate room and cue clearance
The required room length is the playing length plus one cue length and your movement allowance at each end. The width follows the same calculation.
The cabinet must also fit inside that rectangle. The calculator takes the larger requirement on each axis, so a very short cue cannot hide an oversized cabinet.
The fictional example uses a Centennial 8 ft table, a 550 × 440 cm room and a 147.32 cm cue. The cue is 58 inches, the standard length in Brunswick’s room guide.
The example adds 10 cm of movement space per side. This is your chosen extra space beyond the cue.
The exact requirement is 223.52 + 2 × (147.32 + 10) = 538.16 cm long. Across the room, 111.76 + 2 × (147.32 + 10) = 426.4 cm.
The result shows 538 cm of length and 426 cm of width needed, with zero shortfall. Each end has 163 cm from cushion to wall, leaving 5.92 cm after the cue and allowance.
Each long side has 164 cm from cushion to wall and 6.8 cm spare. Fit decisions use the unrounded measurements, even when displayed dimensions round to whole centimetres.
A shortfall is the extra whole room length or width needed. Negative spare space identifies a side where the cue and entered movement allowance extend beyond the wall.
Choose Across room to turn the table by 90 degrees. Head and foot remain the table’s short ends, even when they face the room’s width.
Brunswick’s room size guide explains cue-length planning. This calculator uses your own cue and movement entries instead of treating a published room chart as a guarantee.
Check the room in use
A rectangular clearance result assumes a centred table, symmetric rails and clear parallel walls. Furniture and fixed obstructions need their own checks at cue height.
Mark the cabinet outline on the floor and try your actual cue around it. Test a backswing beside each wall, including corners and places where you bend into a stance.
Include door swings, radiators and pillars in that trial. A shorter cue can change the calculation, but the result alone cannot establish comfortable play.
Measure the delivery route separately, including door openings, stairs and tight turns. Use the supplier’s packed or dismantled component dimensions for access.
Floor suitability depends on the table’s actual weight, its support points and the building. The clearance result does not assess structural capacity or approve installation.