Wall art size guide for your measured space

Compare outer artwork dimensions and gaps with your measured wall or furniture width.

Measure your reference

Measurement unit

Measure the wall span or furniture width you want to compare.

Use the available height above furniture, or leave blank.

Choose the arrangement

Arrangement

The grid has two columns with this gap between cells.

Enter the outer sizes

Artwork 1

Artwork 2

Artwork 3

Reference width occupied

80%

Outer dimensions include the frame. The diagram centres the arrangement on the reference.

80% of reference width occupied. The arrangement is within the entered reference.

Arrangement dimensions

Total width

144 cm

Total height

64 cm

Width left over

36 cm

Height left over

56 cm

The arrangement is within the entered reference.

Scaled layout

Reference 180 cm123Layout 144 cm wide64 cm high
Artwork outer dimensions
ArtworkWidthHeight
144 cm64 cm
244 cm64 cm
344 cm64 cm

Measure the reference and the framed work

This wall art size guide compares actual artwork dimensions with the wall span or furniture width you measure. The result shows the arrangement’s footprint and remaining clearance.

Use Reference width for the span you want to compare. For a sofa-width reference, the percentage describes how the artwork compares with the sofa. It does not establish the wall’s boundaries.

Enter the available wall height above furniture when you also want a vertical comparison. Leave it blank to calculate width alone.

Use each artwork’s full outer width and height, including its frame and mount. A visible print measuring 40 by 60 cm could have a 44 by 64 cm outer frame in a fictional example.

Enter 44 by 64 cm for that framed work. Entering 40 by 60 cm would understate its footprint by 4 cm in each direction.

Choose centimetres or inches before entering measurements. Switching units converts the existing measurements, using the exact 2.54 cm per inch in NIST’s conversion table.

The percentage reports the dimensions you enter. There is no mandatory artwork-to-furniture ratio or automatic size recommendation.

Arrange and compare the pieces

For a row, add every artwork width and the gaps between pieces. Total height is the tallest work. A column adds the heights and gaps, with the widest work setting its width.

The two-column grid uses the widest artwork in each column and the tallest artwork in each row. Pieces sit at each cell’s top-left corner, so smaller pieces leave extra space within their cells.

The fictional starting example has three 44 by 64 cm framed works and two 6 cm gaps. Its width is 44 + 44 + 44 + 6 + 6 = 144 cm.

Against a 180 cm reference, that occupies 80% of the width and leaves 36 cm in total. Centring leaves 18 cm on each side.

With 120 cm of available height, the 64 cm arrangement leaves 56 cm in total, or 28 cm above and below when centred.

Change Number of artworks to 1 for a single 44 by 64 cm work. It occupies 24.44% of the same width and leaves 136 cm across the reference.

Change Reference width to 140 cm while keeping all three pieces. The 144 cm arrangement occupies 103% and shows -4 cm of width left over.

The diagram keeps the product dimensions and shows the overflow. Revise the reference, gaps or selected artwork dimensions to compare another arrangement.

Print the layout and check the room

Download printable layout saves an HTML file with a labelled scale diagram and each artwork’s dimensions. Open the file in your browser and print at 100% or actual size.

Turn off fit-to-page and browser headers and footers. Measure the separate calibration bar: it must be 50 mm long on the printed page.

The document states its scale, chosen to fit the complete layout including overflow. If the calibration bar is the wrong length, correct the print setting before measuring the diagram.

This free local diagram uses the entered measurements. It is separate from a photo-based appearance preview and does not infer dimensions from a room photo.

The numbered rectangles show outer footprints. They do not show hanging points or account for wall construction and fixings.

Confirm the product’s measured outer dimensions and its installation instructions before choosing where to mount it. This layout provides no structural or installation advice.