Dining table size guide for seating and room space

Enter the table shape, seating and room dimensions to compare declared table sizes and clearance, with visible spacing assumptions.

Table measurements

Input units
Table shape

The edge with the rows of seats.

Seating allowances

Rectangles use the two length edges, without end seats.

Your chosen eating width, allowing for the chair.

Room and clearance

In the direction of the table’s length.

From the table edge to the wall or obstruction.

Spacing comparison

Meets allowances

Centred table; compare your entered allowances.

Seating and space

Seat span

60 cm

Minimum table size

180 cm

Table size shortfall

0 cm

Nearest wall gap

110 cm

Wall gap shortfall

0 cm

Results use cm. Minimum size is the rectangle’s length or the circle’s diameter.

Gap on each side

Centred table clearances
SideGap
Left115 cm
Right115 cm
Top110 cm
Bottom110 cm

A negative gap means the table extends beyond that room edge.

Meets allowances. Minimum table length 180 cm. Nearest wall gap 110 cm.

Separate table size and usable seating

This dining table size guide compares your tabletop measurements with your seating allowance and the room gap you want. A match means those entered allowances fit the model.

A rectangular table uses its length and width. The calculation spreads your seats over the two length edges, putting an extra seat on one side for an odd count. It excludes end seats.

For a round table, diameter is the distance across the centre. Seats are evenly spaced around the circle. The tool compares your allowance with the straight span between adjacent seating positions.

That span is a chord, not the curved edge between positions. For six seats on a 120 cm diameter, the straight span is 60 cm. The curved edge is about 62.83 cm.

IKEA’s dining table guide suggests about 60 cm of eating space per person. Change the allowance for your actual chairs and the space you want.

Seat span is a spacing comparison. The calculation does not subtract table legs, check knee room or model chair arms. A maker’s six-seat label describes its own table and chair assumptions.

Check a rectangular and round example

The fictional example starts with a 180 × 90 cm table and six seats. At 60 cm per seat, three people on each length edge need 180 cm.

The table is centred in a 400 × 320 cm room. Its top and bottom gaps are 110 cm each. The left and right gaps are 115 cm each.

With a 110 cm gap wanted on every side, the example meets both allowances. Reducing the table length to 170 cm creates a 10 cm table size shortfall.

For the round example, choose Round and keep the 120 cm diameter, six seats and 60 cm allowance. The minimum diameter is 120 cm.

The same room leaves 140 cm above and below the round table, with 100 cm on its left and right. Seating meets the allowance, but the nearest gap falls short by 10 cm.

The rectangular rule is seats on the fuller side multiplied by Space per seat. The round rule divides Space per seat by the sine of 180 degrees divided by Seats wanted.

Subtract the table dimension from the room dimension, then halve the remainder for each opposing gap. For a quarter-turn, swap the room’s length and width entries.

IKEA’s room spacing guide suggests about 110 to 120 cm for pulling out a chair and passing it. The example uses 110 cm as an editable preference.

Choose centimetres or inches for entry. Switching units converts the measurements without changing the scenario. Returned dimensions stay in centimetres (cm), using 2.54 cm per inch.

Measure access and chairs

Measure the actual chair pulled out from the table, then check the remaining walking space. Table-to-wall distance includes the chair’s occupied depth.

Check chair width and arm height against the table’s clear opening. Pedestals, corner legs and a low apron can restrict seating even when the edge-space calculation passes.

Use the clear room area after allowing for cupboards and other furniture. Open nearby doors and drawers with the chairs occupied. The model assumes a rectangular room and a centred table.

A clearance value does not establish accessibility compliance. Check the layout against the needs of the people using it and any applicable access requirements.

Measure the delivery route separately, including door openings and tight turns. Compare the maker’s packaged dimensions, assembly instructions and removable parts before ordering.