Fridge size guide and clearance comparison

Compare fridge dimensions and stated clearances with your available space.

Measure your space

Measurement unit

Use the narrowest clear width.

Use the lowest clear height.

Measure to the furthest allowed closed front.

Enter the fridge dimensions

Use the selected model’s external width.

Use the stated external height.

Include doors and handles for this comparison.

Enter model clearances

Door opening (optional)

Total width from the model’s opening diagram.

Total depth from the same opening diagram.

Clear width over that whole opening envelope.

Clear depth from the diagram’s reference line.

Closed-space comparison

Room remains

Remaining after clearances

Width remaining

70 mm

Height remaining

35 mm

Depth remaining

40 mm

Door opening: not checked. Complete all four optional measurements.

Entered dimensions only. Delivery access, drawer removal and installation conditions still need checking.

Room remains. Width 70 mm, height 35 mm, depth 40 mm.

Measure the cavity and fridge

This fridge size guide compares a fridge’s external dimensions and stated clearances with your measured space. A shortfall means the entered dimensions need more room.

Measure cavity width at the front and back, at several heights. Measure height on both sides and depth along both side walls. Enter the smallest usable measurement for each direction.

Account for skirting, uneven walls and projecting fittings. Available closed depth runs from the rear reference surface to the furthest position you can accept the closed fridge’s front.

Cabinet depth can exclude the door or handle. Use a closed depth that includes both here. Fisher & Paykel’s RF522ADX5 sheet lists depth as 695 mm and depth including handles as 730 mm.

Read the selected model’s installation drawing before entering its gaps. This tool adds left and right clearances to width, top clearance to height and rear clearance to closed depth.

Keep the drawing’s reference points consistent. A published cavity dimension that already includes ventilation must not receive the same clearance twice. Integrated cabinetry can require ventilation paths that these rectangular sums cannot assess.

The example’s clearances are fictional. Replace them with the actual model’s requirements, including any larger hinge-side allowance for the chosen installation.

Allow for doors and access

A fridge can pass the closed-space comparison while its doors hit a wall or a drawer cannot come out. Check the opening angle and removal instructions separately.

Fisher & Paykel’s installation guide for the listed ActiveSmart models distinguishes installation arrangements. It states that full drawer and shelf access requires opening past 90 degrees.

If your model supplies a door-opening envelope, enter its total required width and depth. Measure the corresponding clear space from the same reference lines and complete all four optional fields.

The door result subtracts that stated envelope from the separately measured open space. It never calculates hinge geometry from cabinet width. An incomplete set stays labelled Door opening: not checked.

For example, a 1,000 mm opening width in a 950 mm clear area is 50 mm short, even when the closed-space result has room remaining.

Compare the whole drawn area with nearby benches and handles, including where the appliance sits within it. Two bounding dimensions cannot detect every collision.

Measure the delivery route through doorways and turns, including stairs and lift openings. Confirm the packed dimensions and any permitted door removal with the delivery team before ordering.

Read litres and the space result separately

Litres describe a published capacity measure. External width, height and depth describe the space occupied by the appliance. A litre label cannot establish whether the fridge fits.

The RF522ADX5 quick reference guide lists Total gross capacity as 519 L and Volume as 487 L. It splits Volume into 345 L refrigerator and 142 L freezer.

Retain each maker’s capacity label when comparing products. Gross capacity and a listed storage volume can describe different measures. Storage layout and the household’s shopping habits need their own assessment.

The fictional example uses a 900 mm wide, 1,800 mm high and 800 mm deep space. Its fridge measures 790 mm wide, 1,715 mm high and 730 mm deep.

Left and right gaps of 20 mm make the required width 830 mm, leaving 70 mm. Adding 50 mm above gives 1,765 mm, leaving 35 mm.

The 30 mm rear gap makes the required depth 760 mm, leaving 40 mm. Reducing available width to 820 mm produces a 10 mm shortfall.

Zero remaining means the entered limit is reached, with no extra tolerance. The arithmetic neither selects an ideal household capacity nor certifies installation. Use the exact model’s instructions to finish the comparison.